LitezAll 200 Lumen Wireless COB LED Light Bar
The LitezAll Wireless Light bar features convenient, easy push button operation with two selectable brightness levels. Mounting is easy, powerful magnet or keyhole mounts for 2 screws (not included). The light bar includes a peel and stick metal disc that allows you to take advantage of the magnetic mount wherever you'd like. Once the disc is applied to a clean surface, it provides the ideal place to mount the wireless light bar magnetically. The light bar will stay securely in any position or orientation using this mounting method.
For a more permanent installation, keyhole mounts are also provided for easy hanging on 2 screws (screws not included).
The wireless light bar from LitezAll can also be used as a Grab and Go® hand held flashlight.
- Product Q&A
- Push Button On/Off. Choose from 200 Lumens or 100 Lumens
- Energy Efficient COB LED Light
- Mounts Easily with Magnet or Keyhole Mounts
- Peel and Stick Metal Disc Included to Create a Metal Surface Anywhere
- Elegant Appearance
- Crafted of Aircraft Grade Aluminum
- Runs on 3 AAA Batteries (included)
- 6.25" long x 1.25" wide x 1.5" high
Operation: Repeatedly pressing the power button cycles between high brightness, low brightness and off.
Mounting: The Wireless Light Bar has 3 mounting options including magnetic using the peel and stick mounting disc, magnetic and keyhole mount.
Magnet Using Peel and Stick Metal Disc: Select a smooth, flat, non-pourous mounting surface for the light. Be sure to thoroughly clean and dry the surface. Remove the metal mounting disc from the back of the light. Carefully peel the protective backing from the disc. Be careful, the exposed adhesive is very sticky! Press the adhesive side of the mounting disc to the mounting surface and press firmly and evenly on the disc. Allow the metal disc to cure for 24 hours before placing the light. After the adhesive has cured for 24 hours, place the magnetic back of the Light Bar on the mounting disc. Your light is ready to use.
WARNING: MOUNTING DISC CANNOT BE REMOVED EASILY ONCE INSTALLED!
Magnet: The Wireless Light Bar adheres magnetically to most smooth rust-free metal surfaces except aluminum. Do not use the peel and stick metal disc.
Keyhole Mount: Install 2 small self tapping screws in the desired location exactly 4 3/16” apart. Place the light bar over the screws and push down.
Battery Replacement: With the back of the light facing you, open the battery compartment door located on one end of the light by pushing the raised area to the right and raising the door. Remove the old batteries and replace them with 3 new AAA alkaline batteries, negative side first. Close the battery compartment door and push it to the left until it clicks.
Caution: replace all batteries at the same time. Do not install batteries backwards, charge or put in fire. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) Batteries. This may cause batteries to leak or explode. Old or discharged batteries must be recycled or disposed of properly, according to local regulations.
Warning! To prevent serious injury, including temporary or permanent loss of sight do not stare into the light, shine light into eyes or focus the beam using an additional lens. Keep away from infants and toddlers as this product contains small parts.
This product is not a toy! Use this light only as it is intended. Inspect before every use, do not use if parts are damaged, loose or missing.
Save these safety precautions.
QUESTIONS & ANSWERSAsk a Question
I really like the size and pricing options of the LitezAll 200 Lumen Wireless COB LED Light Bar. Is there a similar product that is weather/water resistant. I’d like to use it outside at events to illuminate signs and it may be out in the rain. Also, how long are the batteries good for with full illumination?
Thank you for contacting us! The light bars are not waterproof but they are water resistant and the runtime for these lights is 6 hours. I hope this helps!
What is the color of the light; bright white, soft white, etc.?
It is more of a bright white
can you use this for license plate light as I have no housing for thjs light and I need a light with no wires
I apologize, I would not recommend using this light for your license plate. It is not waterproof.
Is it possible to purchase additional magnets for the COB Led Light Bar? I have changed my mind where I wanted to hang the one I received.
Hello. Actually the light is magnetic and we sell 5 packs of peel and stick metal discs. They can be found HERE. Thank you.
What way do the batteries go in? It doesn't seem to matter which way I try to insert the batteries it doesn't light up.
Please insert the batteries with the negative side (flat side) first. If you are doing so and are sure they are fresh batteries, please call support at 815-223-3393. We're happy to help.